Workshop Tools

Safety information

Safety First Read the operating and safety instruction. Follow them carefully. Maximum safe operating pressure 9 bar (125 psi). Air lines are dangerous - use them correctly Putting into service Before use check cap-retaining screws are secure.If the Air tool is dropped check for cracked components. Check air line pressure before connecting the Air tool.The Air tool should be used only by people trained in the use of pneumatically operated tools. Use Keep hands away from moving parts. Never operate the Air tool near the face or body. Only use Air tool to fit CV boots. If air line pressure exceeds 9 bar fit a regulator. Disconnect the Air tool from the air supply after use.

Installation Information

Operation: 1. Slide boot onto arms, large end first. The arms should just protrude from the small end of the boot. To fit a boot to an inner joint, turn the boot inside out before sliding i onto the Airtools´s arm. 2. Press " + " button until arms open enough to pass over the joint. Keep hands clear of moving parts. The air line can now be disconnected. The arms will remain open until the " - " button is pressed. 3. Place Airtool over CV joint and press release button (" -"). Keep hands away from moving parts. 4. Withdraw the Airtool, leaving the boot in position. Complete the installation in the normal way.

• High quality hot-forging process provides a performance exceeding ASME standard
• Longer beam provides more torque during use
• Patented anti-slip open end grasps nut tight , Zero chamfer box end offer better bite on worn fasterners
• High visibility color filled size mark for easy identification during use
• Full range of Metric sizes for all Professional needs
• Premium Chrome Finish
• Anti-Slip open end
• Zero chamfer box end

• ASME Compliant

• 180 degree rotating flexible heads allow you to apply leverage at any desired angle and get around obstructions in tight areas.
• Premium chrome vanadium steel provides durable life
• Heat treated for maximum strength
• 72 tooth ratchet
• Dual 180 degree swivel ratchet head design
• Mirror Polish Finish

• ASME Compliant

• Registered Design
• 2 second button hold for calibration toggle
• 3 units of calibration toggle as standard - psi, bar & kPa
• Replaceable 2 X AAA batteries power unit (supplied)
• Individually tested and certified against national approved gauges
• IP54 - can be used indoors and outdoors, saving time and increasing service
• Large screen and clear digits - Easy and quick to read - Increasing accuracy and speed of use
• Permanently backlit in use, auto off after 10 seconds no-use - Easy to read in dark workshops or at night - Increased flexibility saving cost and time
• Higher pressure range for multiple applications 4 – 250 psi range (including trucks) - Versatile and flexible saving time and money
• Slimline biomorphic body shape gives increased comfort for the user - Fast to use and handle
• Small ‘stubby’ body is the lightest metal bodied digital inflator on the market - Easy to use with reduced fatigue
• Extremely robust aluminium body with protective rubber bumper - Long accurate life expectancy

• Accuracy: ExceedsCompliant with BS EN12645:2014 Reading Accuracy: 0.1 psi / 0.01 bar / 1 kPa Max Inflation Pressure: 250 psi / 17.2 bar / 1723 kPa Max Inlet Pressure: 260 psi / 18.0 bar / 1795 kPa Inflation Flow (@ 190 psi / 13 bar): 500 l/min / 18 CFM Calibration: 4-250 psi / 0.3-17.2 bar / 30-1723 kPa Battery Type: 2 x AAA (supplied) Hose Length: 0.53 m / 21 in Tyre Valve Connection: Twin hold-on Calibration: 4-250 psi / 0.3-17.2 bar / 30-1723 kPa

• 45° rubber overmold stand for aiming beam upward during prolonged use when the light is equipped with a compact battery pack
• Ergonomic grip with rubber overmold - enhances user comfort and grip during use
• Hand wrist lanyard to keep the light safe and handy
• Battery fuel gauge displays battery status
• Dual function trigger allows momentary or lock-on use
• Metal housing and impact resistant polycarbonate lens with gasketed rubber cap which protects from moisture for harsh jobsite conditions
• Especially useful for long range identification - utility pole/high voltage cable inspection, inspection of long runs of conduit, cast or copper pipe, under ground work, bridge work
• Flexible battery system: works with all MILWAUKEE® M12™ batteries
• The reflector produces narrow centre beam with wide peripheral beam
• Up to 35% longer beam distance than competition - 650 m intense and highly focused beam of light with 750 lumens
• TRUEVIEW™ high definition lighting
• Up to 8 hours of run time with an M12™ REDLITHIUM™ 4.0 Ah battery pack

• NCCJ500-W - Wheel Replacement
• NCCJ500-S - Saddle Replacement
• NCCJ500-P - Hydraulic Pump Replacement
• NCCJ500-FP - Foot Pedal Replacement

• SHOCKWAVE IMPACT DUTY steel (Chrome-Molybdenum) is high quality alloy steel which provides ultimate strength and durability.
• According to DIN 3129 / ISO 2725-2 internal square drive according to DIN 3121 / ISO 1174-2.
• Laser etched size markings for easy identification and won‘t wear off.
• Recessed corners allow torque to be transferred across the flats of the socket rather than producing stress on the points or corners.
• 6 gripping points for best precise fit.

• BPW 6.5 9 tons
• Overall length: 70mm
• Size: 3/4in.Drive x 95mm (oval)
• Designed for extracting the rear axle cover

• Slim profile head with flush direction lever offers better accessibility.
• FOUR FLAT™ sides on socket deter rolling.
• All metal design for maximum durabilty.
• Sockets are stamped with measurements on the flat side for easy-to-read visibility.
• Comes with a removable inner tray perfectly designed to be stored.
• 90 tooth design with 4 °of arc swing for tight work spaces.

• 3 in 1 combination HSS-G drill bit: drilling, threading and deburring in one single operation.
• Suitable for use with battery powered or corded drills.
• Reception: ¼″ hex, E6.3.
• Impact rated : suitable for use with cordless impact drivers when keeping to recommended drilling speed.
• Thread type: metric ISO-thread DIN 13.
• Suitable for drilling in plastics, sheet steel and non-alloyed material up to 800 N/mm².
• Always use a suitable cutting oil.

• This set of tools enables the correct timing to be made when servicing the Vauxhall/Opel chain engines fitted to Vauxhall Agila and Corsa with 1.0 12v X10XE and 1.2 16v X12XE engines
• Agila, Astra-G/H, Combo-C, Corsa-B/C/D, Meriva-A, Tigra-B
• For 1.0 12v X10XE and 1.2 16v X12XE engines
• With X10XE, Z10XE, Z10 XEP, X12XE, Z12XE, Z12 XEP, Z14XEL, Z14XEA engine codes
• Chain driven engines
• 1993-2010

• 3/8 in drive torquew wrench
• High torque accuracy allows for high degree of precision in working conditions
• Handle provides strong, durable and comfortable hand hold
• Allows for percise tightning in a single direction
• 45 Teeth Flex Head
• Comfort Grip Handle
• One Way Click Design (Clockwise)

• 45 Teeth Flex HeadTorque Accuracy CW: +/- 3%
• 20 TO 100LBF.FT
• 27 TO 135Nm

• Professional quality
• Twin hold on connector
• PSI/BAR (1 BAR = 100kPa)
• Rubber boot protection for gauge
• Easy to read gauge

General Information

Timing Tool Kit - 1.3 JTD/HDi Fiat, GM, Suzuki, Ford, PSA

• Application: 1.3 JTD/HDi Diesel engines found in Fiat, GM, Suzuki, Ford, Citroen Nemo and Peugeot Bipper
• Timing tool kit with Camshaft/Crankshaft alignment tools only
• Made in Sheffield
• Full Engine rebuild kit available part number 4773
• Use 6408 (Camshaft Holding Tool) if removing camshaft drive gears

• Part of the PACKOUT™ modular storage system.
• IP 65 rated weather seal to keep out rain and jobsite debris.
• Enough storage capacity to fit power tools like circular saws, grinders, drill drivers.
• 34 kg weight capacity.
• Constructed with impact resistant polymers for jobsite durability.
• Quick-Adjust Dividers allow users to store and organize larger equipment and accessories, such as fittings, connectors or caulk.

• Ultra light robust housing from special plastic
• Includes 1/4in. coupling connector
• Cold insulated handle
• No additional lubricant necessary
• Air pressure is regulated through a button
• Expanding of the joint arms through pneumatic air
• For CV joint boots diameter from 20 120 mm
• Suitable for all universal and original vehicle CV joint boots
• Air exhaust through the handle rear end

• Type M: Cone for angled edges and narrow contours.
• Type H: Flame for contouring.
• Type D: Ball for milling holes and creating concave cuts.
• Type C: Cylindrical ball nose for top and side cutting.
• Includes: Types B ,C ,D, H, M.
• Suitable for unhardened and hardened steel, cast iron and non ferrous metals (aluminium, brass, copper).
• Double cut toothing geometry ensures excellent material removal, low vibrations for easier handling and smaller swarfs.
• According to DIN 8033.