Workshop Tools

• Features a non-slip ratchet.
• 8 x 9, 10 x 11, 12 x 13, 14 x 15, 16 x 18 & 17 x 19 mm
• 90 Tooth Count
• Non- Slip Ends
• 6 Point
• 6 Piece
• Full Polish Chrome

• The 90 tooth count gear allows 4 degree arc swing

• Impact rated socket extensions for facilitated bolt access in restricted areas.
• SHOCKWAVE IMPACT DUTY steel (chrome-molybdenum) is high quality alloy steel which provides ultimate strength and durability.

• Precision machined joint for maximum power transmission with optimum leverage for easy and effortless work.
• Induction hardened cutting edges to cut even the hardest of materials.
• Steel blades are fully forged, hardened and tempered for best durability. Grey titanium surface finish is non reflective and ensures maximum corrosion resistance.
• VDE (DIN EN/IEC 60900) certified tools. Tested to 10,000 volts and guaranteed to 1,000 volts. Tested against cold to -40°.
• Ergonomic grip with softgrip for comfortable handling and good grip.

• M18™ REDLITHIUM™ 2.0 Ah / 4.0 Ah / 5.0 Ah / 6.0 Ah / 9.0 Ah battery packs recharge in 40 min / 80 min / 100 min / 124 min/ 180 min or less
• Recharges all M18™ and M12™ REDLITHIUM™ battery packs
• Recharges in sequence - first in, first to charge - resulting in less time needed to manage charging cycles
• M12™ REDLITHIUM™ 2.0 Ah / 3.0 Ah / 4.0 Ah / 6.0 Ah battery packs recharge in 40 min / 70 min / 80 min / 90 min or less
• Charges MILWAUKEE® batteries on the go, perfect for tradesmen and other professional that can use the down time to re-charge their batteries using conventional 12V sockets

• Interior organiser trays.
• Metal reinforced locking point.
• Constructed with impact resistant polymers for jobsite durability.
• Metal reinforced top handle for easier carrying (only on the large box).
• IP65 rated weather seal to keep out rain and jobsite debris.
• Metal reinforced corners.
• Part of the PACKOUT™ modular storage system.
• Mounting location for the ONE-KEY™ TICK ™.

• All metal design for maximum durabilty.
• FOUR FLAT sides on socket deter rolling.
• 90 tooth design with 4Dg of arc swing for tight work spaces.
• 76 mm extension, 152 mm extension, universal joint
• Deep well sockets: 5 mm, 5.5 mm, 6 mm, 7 mm, 8 mm, 9 mm, 10 mm, 11 mm, 12 mm, 13 mm, 14 mm, 15 mm
• Standard sockets: 5 mm, 5.5 mm, 6 mm, 7 mm, 8 mm, 9 mm, 10 mm, 11 mm, 12 mm, 13 mm, 14 mm, 15 mm

• Dual hole design and groove for security accessories.
• Stamped and ink filled diameter markings and laser etched part number for wear resistance.
• Deep wall construction provides clearance for protruding bolts.
• Non-slip hex geometry to prevent socket and fastener rounding.
• Best fitting thanks to 6 gripping points.
• SHOCKWAVE IMPACT DUTY steel (Chrome-Molybdenum) is high quality alloy steel which provides ultimate strength and durability.

Safety information

Safety First Read the operating and safety instruction. Follow them carefully. Maximum safe operating pressure 9 bar (125 psi). Air lines are dangerous - use them correctly Putting into service Before use check cap-retaining screws are secure.If the Air tool is dropped check for cracked components. Check air line pressure before connecting the Air tool.The Air tool should be used only by people trained in the use of pneumatically operated tools. Use Keep hands away from moving parts. Never operate the Air tool near the face or body. Only use Air tool to fit CV boots. If air line pressure exceeds 9 bar fit a regulator. Disconnect the Air tool from the air supply after use.

Installation Information

Operation: 1. Slide boot onto arms, large end first. The arms should just protrude from the small end of the boot. To fit a boot to an inner joint, turn the boot inside out before sliding i onto the Airtools´s arm. 2. Press " + " button until arms open enough to pass over the joint. Keep hands clear of moving parts. The air line can now be disconnected. The arms will remain open until the " - " button is pressed. 3. Place Airtool over CV joint and press release button (" -"). Keep hands away from moving parts. 4. Withdraw the Airtool, leaving the boot in position. Complete the installation in the normal way.