Workshop Tools

• Precision machined joint for maximum power transmission with optimum leverage for easy and effortless work.
• Induction hardened cutting edges to cut even the hardest of materials.
• Steel blades are fully forged, hardened and tempered for best durability. Grey titanium surface finish is non reflective and ensures maximum corrosion resistance.
• VDE (DIN EN/IEC 60900) certified tools. Tested to 10,000 volts and guaranteed to 1,000 volts. Tested against cold to -40°.
• Ergonomic grip with softgrip for comfortable handling and good grip.

• Interior organiser trays.
• Metal reinforced locking point.
• Constructed with impact resistant polymers for jobsite durability.
• Metal reinforced top handle for easier carrying (only on the large box).
• IP65 rated weather seal to keep out rain and jobsite debris.
• Metal reinforced corners.
• Part of the PACKOUT™ modular storage system.
• Mounting location for the ONE-KEY™ TICK ™.

• Tests the freezing levels of antifreeze and battery fluids
• Automatic temperature compensation
• Includes dropper for collecting fluid and plastic storage case

• Dual hole design and groove for security accessories.
• Stamped and ink filled diameter markings and laser etched part number for wear resistance.
• Deep wall construction provides clearance for protruding bolts.
• Non-slip hex geometry to prevent socket and fastener rounding.
• Best fitting thanks to 6 gripping points.
• SHOCKWAVE IMPACT DUTY steel (Chrome-Molybdenum) is high quality alloy steel which provides ultimate strength and durability.

Safety information

Safety First Read the operating and safety instruction. Follow them carefully. Maximum safe operating pressure 9 bar (125 psi). Air lines are dangerous - use them correctly Putting into service Before use check cap-retaining screws are secure.If the Air tool is dropped check for cracked components. Check air line pressure before connecting the Air tool.The Air tool should be used only by people trained in the use of pneumatically operated tools. Use Keep hands away from moving parts. Never operate the Air tool near the face or body. Only use Air tool to fit CV boots. If air line pressure exceeds 9 bar fit a regulator. Disconnect the Air tool from the air supply after use.

Installation Information

Operation: 1. Slide boot onto arms, large end first. The arms should just protrude from the small end of the boot. To fit a boot to an inner joint, turn the boot inside out before sliding i onto the Airtools´s arm. 2. Press " + " button until arms open enough to pass over the joint. Keep hands clear of moving parts. The air line can now be disconnected. The arms will remain open until the " - " button is pressed. 3. Place Airtool over CV joint and press release button (" -"). Keep hands away from moving parts. 4. Withdraw the Airtool, leaving the boot in position. Complete the installation in the normal way.

• Dual hole design and groove for security accessories.
• Stamped and ink filled diameter markings and laser etched part number for wear resistance.
• Deep wall construction provides clearance for protruding bolts.
• Non-slip hex geometry to prevent socket and fastener rounding.
• Best fitting thanks to 6 gripping points.
• SHOCKWAVE IMPACT DUTY steel (Chrome-Molybdenum) is high quality alloy steel which provides ultimate strength and durability.

General Information

Engine Timing Tool Kit - GM engines.;, Engine Timing Tool Kit - GM engines;,..

• Instructions included
• Also fits Chevrolet Cruze, Orlando 1.4, 1.6, 1.8 and Fiat Croma, Alfa Romeo 159 with 939A4.000 engines
• Applications: Astra-G, Corsa-D, Insignia, Mervia, Signum, Vectra-C & Zafira-B 2003-2011
• Engine timing tool kit for GM engines fitted to Vauxhall/Opel and other vehicles 16v 1.6 and 1.8

• Protected against splashing water at all angles (IP24)
• 2 hooks for hanging
• High powered 2.1A USB charger charges tablets, smart phones, MP3 players and other electronic devices
• Best-in-class performance - outstanding light output 400+ lumens, designed to illuminate large areas
• TRUEVIEW™ high definition lighting
• Job site durability - rugged designed with impact resistant lens to withstand abusive job site conditions
• 180° - 360° adjustable beam - versatile design, allows the user to select between area lighting and task lighting
• Flexible battery system: works with all MILWAUKEE® M12™ batteries

• Type M: Cone for angled edges and narrow contours.
• Type H: Flame for contouring.
• Type D: Ball for milling holes and creating concave cuts.
• Type C: Cylindrical ball nose for top and side cutting.
• Includes: Types B ,C ,D, H, M.
• Suitable for unhardened and hardened steel, cast iron and non ferrous metals (aluminium, brass, copper).
• Double cut toothing geometry ensures excellent material removal, low vibrations for easier handling and smaller swarfs.
• According to DIN 8033.