Workshop Tools
Categories
Important compatibility info
Length | 465 mm |
Width | 148 mm |
Function | Mounting Tool, bellow |
Weight | 2 kg |
Extra Description | Duraboot |
Type | Mounting Tool, bellow |
Additional Information
Safety information
Safety First Read the operating and safety instruction. Follow them carefully. Maximum safe operating pressure 9 bar (125 psi). Air lines are dangerous - use them correctly Putting into service Before use check cap-retaining screws are secure.If the Air tool is dropped check for cracked components. Check air line pressure before connecting the Air tool.The Air tool should be used only by people trained in the use of pneumatically operated tools. Use Keep hands away from moving parts. Never operate the Air tool near the face or body. Only use Air tool to fit CV boots. If air line pressure exceeds 9 bar fit a regulator. Disconnect the Air tool from the air supply after use.
Installation Information
Operation: 1. Slide boot onto arms, large end first. The arms should just protrude from the small end of the boot. To fit a boot to an inner joint, turn the boot inside out before sliding i onto the Airtools´s arm. 2. Press " + " button until arms open enough to pass over the joint. Keep hands clear of moving parts. The air line can now be disconnected. The arms will remain open until the " - " button is pressed. 3. Place Airtool over CV joint and press release button (" -"). Keep hands away from moving parts. 4. Withdraw the Airtool, leaving the boot in position. Complete the installation in the normal way.
Important compatibility info
12V Charge Capacity (up to) | 20 Ah - 180 Ah |
Charge Rate | 12 A |
6V Charge Capacity (up to) | 20 Ah - 180 Ah |
Trickle Charge | No |
Charging Voltage | 12 V |
Important compatibility info
Title | Analogue Tyre Inflator |
Additional Information
- Complete with 3 piece adaptor kit for bikes, air beds and other inflatables
- Large on/off button for easy use with dirty/greasy hands or in poor lighting conditions
- Flat design gives you maximum stability during use
- Valve cap storage compartment for safe keeping when inflating
- Fitted with 3m power cable and fused 12V DC power plug to help you reach around the vehicle
- Screw stem valve connector helps reach awkwardly placed tyre valves
- Flexible air hose with easy access storage compartment specifically designed to reduce kinks
- 40mm diameter analogue pressure gauge in PSI, BAR, kPA
- Inflates a tyre in 4.5 minutes
Important compatibility info
Additional Information
- Complete with 2 piece adaptor kit for bikes; air beds and other inflatables
- Easy to read digital display
- Compact for easy storage and transportation
- Built in white LED light
- Rechargeable with power bank function
- 4 programmable pressure settings with digital autostop for ease of use
- Inflates bicycle tyre in <2 minutes
- Versatile - Ideal for cars; motorbikes and bicycles
- EU Conforms: Electromagnetic Compatibility - Directive 2014/30/EU Restriction of Hazardous Substances (RoHS) - Directive 2015/863/EU Regulation (EC) No1907/2006 - REACH Machinery Directive 2006/42/EC UK Comforms: Electromagnetic Compatibility Regulations 2016 Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment Regulations 2012 Regulation (EC) No1907/2006 - REACH Supply of Machinery (Safety) Regulations 2008
Important compatibility info
Title | Digital Tyre Pressure & Tread Depth Gauge |
Additional Information
- Comes complete with a handy storage case
- Range 0-99 psi / 0-7 bar
- Measures in PSI, bar, kpa, Kg/Cm2
- Tread depth gauge to measure tyre tread depth
- Unique 360 degree rotating nozzle and LED light to assist in locating tyre valve
- Dimensions (MM): H 141 x W 40 x D 29
- Weight (kg): 0.094
- Batteries: 2x CR2032 Included
Important compatibility info
Title | Emergency Tyre Kit |
Additional Information
- Comes With A Handy Carry Case To Store Neatly In Your Boot
- Includes: Tyre Inflator, Tyre Pressure Gauge, Tread Gauge, 1 x Pair Of Protective Gloves, 2 x Cleaning Wipes
- 6 Piece Emergency Tyre Kit
- Conforms with relevant Applicable UK Legislation: Electromagnetic Compatibility Regulations 2016 The Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment Regulation 2012 Regulation (EC) No1907/2006 - REACH Supply of Machinery (Safety) Regulations 2008 References to the relevant UK Designated Standards used or references to other technical specifications in relation to which conformity is declared: EN 50498:2010
Important compatibility info
Additional Information
- The Stanley 197483 has 512 different configurations, the Stanley 'Sortmaster' organiser can be customised for storing different sized tools
- Also ideal for stopping movement from one compartment to another during transport
- Can be used also for small items and fixings
Important compatibility info
Title | Tyre Inflator - 12V - Compressor With Gauge & Light - 0-260 PSI |
Additional Information
- 12v car cigarette lighter plug
- Built-in air pressure gauge and storage compartment
- High speed inflation of tyres and other inflatable objects
- Built in work light and flashing hazard light
- 260 PSI air compressor
- Oblong style 3 in 1 product
- CE, ROHS, REACH, GS TUV Compliant
Important compatibility info
Title | Wheel Brace - 4 Way - Blue |
Additional Information
- GS/TUV Approved
- Sizes 17mm & 19mm - 21mm & 23mm
- CE, ROHS, REACH, GS TUV Compliant
Important compatibility info
Title | Tyre Inflator - 12V - Compressor With Digital Gauge - 0-150 PSI |
Additional Information
- Built in storage space for hose, power lead & valve adaptors
- Cuts off when selected pressure level is reached
- Ideal for roadside emergencies
- Compact and lightweight, take it anywhere you go
- Comes with a digital display and a 2 piece adaptor kit
- Ideal for inflating tyres and other inflatable objects
- This simple to use air compressor automatically cuts off when the pre selected pressure level is reached
- CE, ROHS, REACH, GS TUV Compliant
Important compatibility info
Title | Multi-Use Syphon & Air Pump |
Additional Information
- The outside diameter is 1.3cm
- The size of the tube inside is 1cm
- 16in. air pressure hose
- 2 x 51in. Hose
- For the use with motor vehicles/motor bikes/cycles and more
- Inflate balls, bicycles tyres, beach toys
- Transfer oil, petrol and other liquids
- CE, ROHS, REACH, GS TUV Compliant
Important compatibility info
Title | Wheel Brace - 4 Way - Silver |
Additional Information
- GS/TUV Approved
- Sizes 17mm & 19mm - 21mm & 23mm
- CE, ROHS, REACH, GS TUV Compliant
Important compatibility info
Title | 2 Tonne (2000kg) Trolley Jack with Moulded Case |
Additional Information
- Manual provided
- in.Weight: 8.4kg in.
- in.360 degree lifting saddle in.
- in.Fitted with swivel castor wheel for ease of positioning in.
- in.Includes extension handle in.
- Lifting range: 135mm to 330mm
Important compatibility info
Title | 2 Tonne (2000kg) Hydraulic Vehicle Trolley Jack |
Additional Information
- Manual provided
- in.Weight: 8.4kg in.
- in.360 degree lifting saddle in.
- in.Fitted with swivel castor wheel for ease of positioning in.
- in.Includes extension handle in.
- Lifting range: 135mm to 330mm
Important compatibility info
Title | Tyre Pressure Gauge - Analogue - Chrome |
Additional Information
- Tough & shock proof metal body
- Spring pocket clip
- Capacity 10-50 psi
- Angled head fitting
- CE, ROHS, REACH, GS TUV Compliant
Important compatibility info
Title | Tyre Tread Depth Gauge - Analogue |
Additional Information
- Check your tyre tread depth on a regular basis
- Gives accurate readings
- Sturdy metal construction
- CE, ROHS, REACH, GS TUV Compliant
Important compatibility info
Title | De-Luxe Quality Twin Cylinder Foot Pump (270 Gauge) |
Additional Information
- Product Dimensions (L x W x H): 24 x 15 x 8.5cm
- Max Pressure (PSI): 100psi
- Features an analogue display pressure gauge that provides readings in both PSI and Bar
- Suitable for inflating tyres on cars, motorcycles & bicycles and it has a trigger lock valve adaptor. It also comes supplied with two nozzle adaptors for inflating footballs, cushions and other inflatables
- It also has a wide base that provides better stability when the foot pump is in use as well as a anti-slip tread plate. Plus, the pump has a retaining clip that runs the whole width of the foot pedal which makes it more secure when storing the foot pump
- Comes with a reinforced base at the bottom of both cylinders which enables the rods to smoothly glide into barrels. This helps to reduce strain on the cylinder end caps on both barrels
- This deluxe 100PSI double barrel foot pump is designed to provide you with a long lasting performance
- Conforms to EN16051:2012
Important compatibility info
Title | De-Luxe Quality Single Cylinder Foot Pump (270 Gauge) |
Additional Information
- Product Dimensions (L x W x H): 24 x 9 x 8cm
- Flow rate: (Litres/Min): 100psi
- Max Pressure (PSI): 100psi
- For accurate tyre pressure maintenance it is recommended that you check your tyre pressure on a regular basis
- With a built in pedal locking bar, assists easy storage when not in use
- Includes special adaptors for bicycles, footballs, cushions and other inflatables
- Supplied with a 100psi/0.7 bar pressure gauge, a 24” hose with rust proof valve connector
- Also suitable for balls, toys, and many other inflatable objects
- Single Barrel Foot Pump is suitable for car, motorcycle & bicycle tyres
- Conforms to EN16051:2012
Important compatibility info
Important compatibility info
Additional Information
- They are used as a general-purpose soft-faced hammer in automotive and general engineering for assembly, repair and maintenance
- These copper hammers have faces that are designed to wear and can be easily replaced as spare faces are available
- Ideal where a heavy blow is required combined with a relatively small striking area
- The malleable Iron head provides the weight for the blow and the Copper faces also provide weight whilst transferring the force to the item being struck without fear of damage
- Thor copper hammers have a malleable Iron head fitted with two cylindrical faces of pure electrolytic copper on a wooden shaft
- Weight: 850g
Important compatibility info
Additional Information
- They are used as a general-purpose soft-faced hammer in automotive and general engineering for assembly, repair and maintenance
- These copper hammers have faces that are designed to wear and can be easily replaced as spare faces are available
- Ideal where a heavy blow is required combined with a relatively small striking area
- The malleable Iron head provides the weight for the blow and the Copper faces also provide weight whilst transferring the force to the item being struck without fear of damage
- Thor copper hammers have a malleable Iron head fitted with two cylindrical faces of pure electrolytic copper on a wooden shaft
- Weight: 1975g
Important compatibility info
Title | Mig Welding Wire - Aluminium - 0.8mm - 0.5Kg |
Additional Information
- AWS A5.9
- Welding wire for welding
Important compatibility info
Title | Mild Steel Mig Wire - 0.6mm - 0.7kg |
Additional Information
- SG2 A18 ER70S-6
- Mild steel welding wire for welding low and medium tensile steels
Important compatibility info
Title | Mild Steel Mig Wire - 0.8mm - 0.7kg |
Additional Information
- SG2 A18 ER70S-6
- Mild steel welding wire for welding low and medium tensile steels
Important compatibility info
Title | Welding Tips - 0.8mm - 140 - Pack of 10 |
Additional Information
- Contact tips for welding with welding wire in torches
Important compatibility info
Title | Mild Steel Mig Wire - 0.6mm - 15kg |
Additional Information
- SG2 A18 ER70S-6
- Mild steel welding wire for welding low and medium tensile steels
Important compatibility info
Title | Mild Steel Mig Wire - 1.0mm - 15kg |
Additional Information
- SG2 A18 ER70S-6
- Mild steel welding wire for welding low and medium tensile steels
Important compatibility info
Title | Welding Tips - 1.0mm - 250 - Pack of 10 |
Additional Information
- Contact tips for welding with welding wire in torches
Important compatibility info
Title | Mild Steel Electrodes - 3.2mm - Pack of 10 |
Additional Information
- AWS A5.1 E6013
- Pack of 10 electrodes
- electrodes for MMA (stick) welding of mild steel
Important compatibility info
Title | Mild Steel Mig Wire - 0.6mm - 5kg |
Additional Information
- SG2 A18 ER70S-6
- Mild steel welding wire for welding low and medium tensile steels
Important compatibility info
Title | Mild Steel Mig Wire - 0.8mm - 5kg |
Additional Information
- SG2 A18 ER70S-6
- Mild steel welding wire for welding low and medium tensile steels
Important compatibility info
Title | Regulator Adaptor - Female to Bullnose - CO2 to Argon & Argon/CO2 |
Additional Information
- Also suitable for use with regulators from other brands
- Allows one regulator to be used on multiple types of gas bottles
Important compatibility info
Title | Tyre Tread Depth Gauge - Analogue |
Additional Information
- Legal limit 1.6mm
- Sold as a single
- Metal/Plastic
Important compatibility info
Title | Tyre Valve Cores - Short 43mm - Pack Of 4 |
Additional Information
- Can be used on some cycles
- Normal length 43mm valves
- Tyre valve cores
Important compatibility info
Title | Car Dust Caps - Black Plastic - Pack Of 4 |
Additional Information
This pact of plastic dust caps can be used to prevent dirt from entering into the Schrader valve on tyres. They also help stop air from escaping through the valve and reducing the pressure of your tyre. These black plastic dust caps come as a pack of 4.
Pearl Products is a family run business that supplies the automotive market with accessories and aftermarket solutions. It is the largest family run business of its kind in the market today and aims to provide a high quality, single source solution to its customers. Pearl boasts a product portfolio in excess of 4000 part numbers, with ranges covering anything from replacement parts to workshop consumables.
- Easy grip
- Standard thread
- These caps are used to stop dirt entering the schrader valve on tyres
Important compatibility info
Title | Car Dust Caps With Key - Chrome Metal - Pack Of 4 |
Additional Information
- Easy grip
- Standard thread
- These caps are used to stop dirt entering the schrader valve on tyres
Important compatibility info
Title | Tyre Valve Tool - Multi Use Tool |
Additional Information
Pearl has established a reputation over the years for delivering high quality products. With recent expansions into a more diverse product portfolio of automotive products, its established Wot Nots' brand is still thriving. Pearl boasts a product portfolio in excess of 4000 part numbers, with ranges covering anything from replacement parts to workshop consumables.
- 4 prong tool
- Remove stone from tyres etc.
- Tyre valve tool multi use, can be used to unscrew inner valve
Important compatibility info
Additional Information
- Brake fluid resistant
- The split is normally held below the fluid level in a container to stop air ingress
- Brake bleed tube made of soft rubber, connect to a bleed valve and has a split the other end allowing fluid to be expelled into a container
Important compatibility info
Title | Car Dust Caps - Chrome Metal - Pack Of 4 |
Additional Information
Pearl has established a reputation over the years for delivering high quality products. With recent expansions into a more diverse product portfolio of automotive products, its established Wot Nots' brand is still thriving. Pearl boasts a product portfolio in excess of 4000 part numbers, with ranges covering anything from replacement parts to workshop consumables.
- Easy grip
- Standard thread
- These caps are used to stop dirt entering the schrader valve on tyres