Workshop Tools

• Most commonly used for the cleaning and removal of corrosion on metal
• Made from steel strands
• Brush constructed of wood housing wire strands, available in four, three or two rows

• Reduces the Power Probe tip battery voltage to 5V and limits the current output works with PP3EZREDAS
• Simple add-on accessory that works with all Power Probes with 4mm banana tip
• Safely simulate sensor reference voltages and outputs without damaging components

• Voltage Output: 5V regulated output
• Connector Type: Standard 4mm banana connector
• Compatibility: Works with Power Probe Circuit Testers (PPBasic, PP3 Series, PP4 Series, Pro Series)
• Adapter Requirement for Older Models: Requires banana jack conversion kit (#PNLS020A) for PP1 and PP2 models
• LED Indicator: Red LED illuminates to show active 5V output
• Ground Connection: Includes auxiliary ground lead clip for secure grounding
• Durability: Built with rugged materials for long-term use
• Use Case: Supplies a stable 5V to test circuits and components in vehicles
• Dimensions and Weight: Compact and lightweight for easy portability.

• Service Your Vehicles Safely: Electric and hybrid vehicles feature battery systems that need to be disconnected to prevent error or shock prior to service; Use the Power Probe VT750 LCD Car Voltage Meter Tester to ensure your battery voltage reads zero be
• Reliable Detection for Optimal Safety: Auto electric tester tool has a voltage rating from 12 to 750 volts and overvoltage protection up to 1000 volts AC/DC
• Compact Two-Prong Design: 9.4-inch (23.9cm) fixed probe housing and secondary electrical tester pole work together to prevent false readings and measure accurate, exact voltage (AC/DC) current
• Quality You Can Trust: Thick material ensures durability for the volt meter, while the retracting insulators help prevent any accidental shorts between the probes or surrounding objects
• Easy To Use: 10 minutes after disconnecting the 12-volt and high-volt batteries, complete a Live-Dead-Live test; Check 12v battery for a baseline, check high-volt battery for a dead or zero reading, then re-verify the electrical meter is still functioning

• Voltage Testing Range: 12V to 750V AC/DC
• Continuity Testing: Audible beep for continuity detection
• Display: LCD with clear digital readings
• Voltage Indication: Provides AC and DC voltage differentiation
• Polarity Detection: Identifies positive and negative poles
• Safety Compliance: CAT III 750V certification
• Response Time: Quick response for voltage and continuity checks
• Overvoltage Protection: Protects the device during high voltage surges
• Power Source: No batteries required, powered by the voltage under test
• Operating Environment: Designed for 0°C to 40°C, with 80% relative humidity tolerance
• Build Quality: Durable, ergonomic design with protective housing
• Probes: Integrated test probes with secure connectors.

• A professional tool for the bodyshop
• Manufactured from 1055 medium carbon steel
• Large polished surface enables the metal to be worked without damage to the paint work
• Weight - 355 grams
• Length - 260mm

• Use on internal and external trim
• Composite material
• Anti scratch
• For the safe removal of trim and clips used on modern vehicles

• Pack of 5
• 280 micron mesh filters
• Designed for DeVilbiss, SATA and Iwata spray guns
• Gravity feed gun filter

• Dispenser pack with label
• Handle bends to any angle
• More economical than paint brushes
• Also useful for applying adhesive or lubricant application
• Ideal for small touch ups, stone chips etc.

• Special profile
• Consumable
• Bag of 100
• For use with the Power-TEC hot stapler
• Stainless steel staples

• Suitable for spot repair
• Complete with regulator

• Pack of 100
• Ideal for body shop use
• Height 76mm diameter 40mm
• Volume 60ml
• Leak protection in liner
• Built in brush

• Consumable item
• Pack of 15
• Made in Europe
• REACH Certified
• For use with all glue pulling systems

• Max 4000 rpm
• Supplied with an adaptor for drill use
• Removes stripes/stickers moulding glue etc
• Fluted abrasive disc

• Insulation Test with PI/DAR/Timed
• mA-selectable mode
• Auto bi-direction continuity Test
• Visual/acoustic compare function
• Auto AC/DC Voltage Test with LPF
• 1500 records of Store/Recall

• Measures AC Voltage(ACV)
• DC Voltage(DCV)
• Frequency
• Earth-bond Resistance(Continuity)
• Capacitance
• Insulation Resistance
• Features Auto-sense mode for automatic detection of ACV or DCV
• Insulation test range: 50V to 1000V with maximum resistance range up to 200GΩ
• Earth-bond resistance measurement range: 0.01Ω to 40.00kΩ
• Capacitance measurement range: 0.1nF to 10.00uF
• Bluetooth Low Energy(BLE) V5.0 for wireless data transfer
• Compliance with IEC/EN 61010-1 and IEC/EN 61557 standards
• IP40 rated for dust resistance
• operates up to an altitude of 2000m
• True RMS measurements
• automatic discharge function
• CAT IV 600V rated
• supports up to 1500 stored readings
• Auto power-off for battery preservation
• Dimensions: 96mm x 207mm x 54mm
• weight: 630g
• powered by 4 AA batteries.

• Tests Bad Grounds and Short Circuits
• Supplies Power and Ground
• Digital Voltmeter with Min/Max Voltage Capturing
• Navigation Menu for EZ Learning

• Voltage Detection Range: Supports low and high AC voltage detection
• LED Indicators: Visual indication of circuit status and voltage presence
• Non-Contact Operation: Safely detects voltage without direct contact
• Frequency Compatibility: Operates effectively at standard electrical frequencies
• Durability: Designed for robust field use with protective casing
• Ease of Use: Features ergonomic design and intuitive operation
• Compliance: Adheres to international electrical safety standards
• Battery Operated: Uses standard alkaline batteries for portability.

• Switch latch for constant power
• Automatic circuit breaker reset
• Auxiliary ground lead holder

• Voltage Detection Range: Detects low to high AC voltages
• Non-Contact Operation: Ensures safety during electrical testing
• LED Indicators: Provides visual feedback for voltage detection
• Compact Design: Small and lightweight for convenient use
• Frequency Compatibility: Operates at standard electrical frequencies
• Durability: Engineered for regular use with robust construction
• Battery Operated: Powered by alkaline batteries
• Compliance: Meets international electrical safety standards.

• Power Probe OBD II Breakout Testing Box
• Tests DLC (OBD port) for any abnormalities, such as shorting or reverse polarity at the pins before connecting other diagnostic equipment.
• quickly accss all 16 pins connections during repair and diagnosois of the vehicle

• Voltage Monitoring Range: 7.0V to 30.0V DC input
• Maximum Load: Up to 3.0A output
• Overload Protection: PTC self-healing fuse
• LED Displays: 3-digit resolution of 0.1V
• Banana Sockets: 16 outputs with 1.0mm diameter and LED indicators
• Protocols Detected: PWM (J1850)
• VPW (J1850)
• ISO 9141-2
• DIS/ISO 14230-4
• CAN bus (J-2284)
• Temperature Range: Suitable for automotive environments
• Humidity Tolerance: Less than 70%
• Cable Length: 30 inches (0.8 meters)
• Polarity Protection: Detects reverse polarity with red LED for pins 4 and 5
• Voltage Alerts: Slow beeps for low voltage (<11.8V for 12V systems)
• fast beeps for high voltage (>15.5V for 12V systems)
• Diagnostic Features: Monitors individual pins for voltage presence
• detects communication protocol signals
• DLC Connector Flashlight: Built-in light for easier connection
• Battery Type for Flashlight: CR1220 coin battery.

• Signal Locking will show the correct direction to a short to ground
• Signal distance bar indicates distance height from short to ground or open circuits
• LED light on receiver illuminates the work space area
• Longer 10-minute Auto shut off time

• Operating Voltage (Transmitter): 6V-48V DC
• Current Consumption (Transmitter): <200mA
• Operating Voltage (Receiver): 2 AAA batteries
• Signal Frequency: 4kHz polarized signal
• Circuit Testing Modes: Open circuit tracking
• short circuit tracking
• ground circuit tracking
• Operating Temperature: Up to 50°C
• Storage Temperature: Up to 70°C
• Maximum Humidity: 80% non-condensing
• Altitude Limit: <2000m
• Signal Detection: Indicates short and open circuits using visual and audio cues
• Sensitivity Adjustment: Adjustable for varying signal strengths
• Auto Shutoff: Receiver turns off after 10 minutes of inactivity
• Accessories Compatibility: Standard 4mm banana jack connectors for custom adapters
• Cable Length: 6m transmitter power cable for extended reach.

• Spectral Response 8-14 μm
• Laser <1mW / 630-670nm
• °C / °F Selection

• Temperature Range: -20°C to 500°C (-4°F to 932°F)
• Accuracy: ±3°C for -20°C to 0°C
• ±(2.0% of reading + 2°C) for 0°C to 500°C
• Optical Resolution: 10:1 distance-to-spot ratio
• Spectral Response: 8–14 μm
• Repeatability: ±1°C
• Response Time: Approximately 1 second
• Emissivity: Fixed at 0.95
• Laser Class: Class 2, <1mW, wavelength 630-670nm
• Display: Backlit LCD with MIN, MAX, and AVG readings
• Units: °C/°F selectable
• Auto Power-Off: Turns off after 10 seconds of inactivity
• Power Source: 2 AAA batteries
• Operating Environment: 0°C to 40°C, 10%-90% relative humidity
• Dimensions: 143mm x 99mm x 47mm
• Weight: Approximately 160g (including batteries)
• Safety Compliance: Conforms to EN61326, EN61010-1, EN60825-1, UL STD 61010-1, CSA STD C22.2 No.61010-1.

• ADJUSTABLE DUTY CYCLE from 5% to 100% with side buttons
• COMPATABLE WITH all Power Probe models with a 4mm banana jack in/out
• EASY INSTALL by removing power probe tip and inserting adapter into banana jack
• GREAT FOR diagnosing circuit fan issues

• Voltage Range: Operates between 9V and 24V DC
• Current Capacity: Maximum 40A output
• Frequency Range: Adjustable pulse width modulation (PWM) frequency from 10Hz to 200Hz
• Duty Cycle Range: Adjustable from 0% to 100%
• Input Protection: Overvoltage and reverse polarity protection
• Output Control: Variable output power via rotary dial
• Dimensions: Compact enclosure design for portability
• Connection Interface: Equipped with standard terminals for easy wiring
• Operating Temperature: -20°C to 60°C
• Housing: Durable and lightweight for automotive or workshop use
• Indicators: LED indicators for power status and output activity.

Safety information

Safety First Read the operating and safety instruction. Follow them carefully. Maximum safe operating pressure 9 bar (125 psi). Air lines are dangerous - use them correctly Putting into service Before use check cap-retaining screws are secure.If the Air tool is dropped check for cracked components. Check air line pressure before connecting the Air tool.The Air tool should be used only by people trained in the use of pneumatically operated tools. Use Keep hands away from moving parts. Never operate the Air tool near the face or body. Only use Air tool to fit CV boots. If air line pressure exceeds 9 bar fit a regulator. Disconnect the Air tool from the air supply after use.

Installation Information

Operation: 1. Slide boot onto arms, large end first. The arms should just protrude from the small end of the boot. To fit a boot to an inner joint, turn the boot inside out before sliding i onto the Airtools´s arm. 2. Press " + " button until arms open enough to pass over the joint. Keep hands clear of moving parts. The air line can now be disconnected. The arms will remain open until the " - " button is pressed. 3. Place Airtool over CV joint and press release button (" -"). Keep hands away from moving parts. 4. Withdraw the Airtool, leaving the boot in position. Complete the installation in the normal way.

• Complete with 3 piece adaptor kit for bikes, air beds and other inflatables
• Large on/off button for easy use with dirty/greasy hands or in poor lighting conditions
• Flat design gives you maximum stability during use
• Valve cap storage compartment for safe keeping when inflating
• Fitted with 3m power cable and fused 12V DC power plug to help you reach around the vehicle
• Screw stem valve connector helps reach awkwardly placed tyre valves
• Flexible air hose with easy access storage compartment specifically designed to reduce kinks
• 40mm diameter analogue pressure gauge in PSI, BAR, kPA
• Inflates a tyre in 4.5 minutes

• Also includes: 1x spare fuse, 4x spare valve caps and 1 x paid of gloves
• Large on/off button for easy use with dirty/greasy hands or in poor lighting conditions
• Directional white LED light gives maximum illumination where you need it
• Flat design gives you maximum stability during use
• Valve cap storage compartment for safe keeping when inflating
• Wind up power cable gets you back on the road faster
• Fitted with extra-long 3.5m power cable and fused 12V DC power plug to help you reach all around the car
• Tyre deflation valve quickly releases unwanted pressure
• Premium brass screw stem valve connector helps reach awkwardly placed tyre valves
• Extra long 70cm air hose with easy access storage compartment specifically designed to reduce kinks
• Easy to read W76 x H48mm digital screen with status bar helping you to keep track in any condition
• Measures in PSI, BAR and kPA
• Automatically stops at the set pressure and remembers it for future use
• Quick setting digital gauge
• Inflates a tyre in 2 minutes

• Complete with 2 piece adaptor kit for bikes; air beds and other inflatables
• Easy to read digital display
• Compact for easy storage and transportation
• Built in white LED light
• Rechargeable with power bank function
• 4 programmable pressure settings with digital autostop for ease of use
• Inflates bicycle tyre in <2 minutes
• Versatile - Ideal for cars; motorbikes and bicycles

• EU Conforms: Electromagnetic Compatibility - Directive 2014/30/EU Restriction of Hazardous Substances (RoHS) - Directive 2015/863/EU Regulation (EC) No1907/2006 - REACH Machinery Directive 2006/42/EC UK Comforms: Electromagnetic Compatibility Regulations 2016 Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment Regulations 2012 Regulation (EC) No1907/2006 - REACH Supply of Machinery (Safety) Regulations 2008

• Comes complete with a handy storage case
• Range 0-99 psi / 0-7 bar
• Measures in PSI, bar, kpa, Kg/Cm2
• Tread depth gauge to measure tyre tread depth
• Unique 360 degree rotating nozzle and LED light to assist in locating tyre valve

• Dimensions (MM): H 141 x W 40 x D 29
• Weight (kg): 0.094
• Batteries: 2x CR2032 Included

• Comes With A Handy Carry Case To Store Neatly In Your Boot
• Includes: Tyre Inflator, Tyre Pressure Gauge, Tread Gauge, 1 x Pair Of Protective Gloves, 2 x Cleaning Wipes
• 6 Piece Emergency Tyre Kit

• Conforms with relevant Applicable UK Legislation: Electromagnetic Compatibility Regulations 2016 The Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment Regulation 2012 Regulation (EC) No1907/2006 - REACH Supply of Machinery (Safety) Regulations 2008 References to the relevant UK Designated Standards used or references to other technical specifications in relation to which conformity is declared: EN 50498:2010

• The Stanley 197483 has 512 different configurations, the Stanley 'Sortmaster' organiser can be customised for storing different sized tools
• Also ideal for stopping movement from one compartment to another during transport
• Can be used also for small items and fixings

• GS/TUV Approved
• Sizes 17mm & 19mm - 21mm & 23mm

• CE, ROHS, REACH, GS TUV Compliant

• Built in storage space for hose, power lead & valve adaptors
• Cuts off when selected pressure level is reached
• Ideal for roadside emergencies
• Compact and lightweight, take it anywhere you go
• Comes with a digital display and a 2 piece adaptor kit
• Ideal for inflating tyres and other inflatable objects
• This simple to use air compressor automatically cuts off when the pre selected pressure level is reached

• CE, ROHS, REACH, GS TUV Compliant

• GS/TUV approved
• Anti-slip handle to assist leverage
• Chrome drive socket
• Extends from 35cm (13.5in.) to 52cm (20.5in.).

• CE, ROHS, REACH, GS TUV Compliant

• The outside diameter is 1.3cm
• The size of the tube inside is 1cm
• 16in. air pressure hose
• 2 x 51in. Hose
• For the use with motor vehicles/motor bikes/cycles and more
• Inflate balls, bicycles tyres, beach toys
• Transfer oil, petrol and other liquids

• CE, ROHS, REACH, GS TUV Compliant

• GS/TUV Approved
• Sizes 17mm & 19mm - 21mm & 23mm

• CE, ROHS, REACH, GS TUV Compliant

• Manual provided
• in.Weight: 8.4kg in.
• in.360 degree lifting saddle in.
• in.Fitted with swivel castor wheel for ease of positioning in.
• in.Includes extension handle in.
• Lifting range: 135mm to 330mm

• Manual provided
• in.Weight: 8.4kg in.
• in.360 degree lifting saddle in.
• in.Fitted with swivel castor wheel for ease of positioning in.
• in.Includes extension handle in.
• Lifting range: 135mm to 330mm

• Tough & shock proof metal body
• Spring pocket clip
• Capacity 10-50 psi
• Angled head fitting

• CE, ROHS, REACH, GS TUV Compliant

• Check your tyre tread depth on a regular basis
• Gives accurate readings
• Sturdy metal construction

• CE, ROHS, REACH, GS TUV Compliant

• Product Dimensions (L x W x H): 24 x 15 x 8.5cm
• Max Pressure (PSI): 100psi
• Features an analogue display pressure gauge that provides readings in both PSI and Bar
• Suitable for inflating tyres on cars, motorcycles & bicycles and it has a trigger lock valve adaptor. It also comes supplied with two nozzle adaptors for inflating footballs, cushions and other inflatables
• It also has a wide base that provides better stability when the foot pump is in use as well as a anti-slip tread plate. Plus, the pump has a retaining clip that runs the whole width of the foot pedal which makes it more secure when storing the foot pump
• Comes with a reinforced base at the bottom of both cylinders which enables the rods to smoothly glide into barrels. This helps to reduce strain on the cylinder end caps on both barrels
• This deluxe 100PSI double barrel foot pump is designed to provide you with a long lasting performance

• Conforms to EN16051:2012

• Product Dimensions (L x W x H): 24 x 9 x 8cm
• Flow rate: (Litres/Min): 100psi
• Max Pressure (PSI): 100psi
• For accurate tyre pressure maintenance it is recommended that you check your tyre pressure on a regular basis
• With a built in pedal locking bar, assists easy storage when not in use
• Includes special adaptors for bicycles, footballs, cushions and other inflatables
• Supplied with a 100psi/0.7 bar pressure gauge, a 24” hose with rust proof valve connector
• Also suitable for balls, toys, and many other inflatable objects
• Single Barrel Foot Pump is suitable for car, motorcycle & bicycle tyres

• Conforms to EN16051:2012

• They are used as a general-purpose soft-faced hammer in automotive and general engineering for assembly, repair and maintenance
• These copper hammers have faces that are designed to wear and can be easily replaced as spare faces are available
• Ideal where a heavy blow is required combined with a relatively small striking area
• The malleable Iron head provides the weight for the blow and the Copper faces also provide weight whilst transferring the force to the item being struck without fear of damage
• Thor copper hammers have a malleable Iron head fitted with two cylindrical faces of pure electrolytic copper on a wooden shaft

• Weight: 850g

• They are used as a general-purpose soft-faced hammer in automotive and general engineering for assembly, repair and maintenance
• These copper hammers have faces that are designed to wear and can be easily replaced as spare faces are available
• Ideal where a heavy blow is required combined with a relatively small striking area
• The malleable Iron head provides the weight for the blow and the Copper faces also provide weight whilst transferring the force to the item being struck without fear of damage
• Thor copper hammers have a malleable Iron head fitted with two cylindrical faces of pure electrolytic copper on a wooden shaft

• Weight: 1300g

• They are used as a general-purpose soft-faced hammer in automotive and general engineering for assembly, repair and maintenance
• These copper hammers have faces that are designed to wear and can be easily replaced as spare faces are available
• Ideal where a heavy blow is required combined with a relatively small striking area
• The malleable Iron head provides the weight for the blow and the Copper faces also provide weight whilst transferring the force to the item being struck without fear of damage
• Thor copper hammers have a malleable Iron head fitted with two cylindrical faces of pure electrolytic copper on a wooden shaft

• Weight: 1975g

• AWS A5.9
• Welding wire for welding

• Contact tips for welding with welding wire in torches

• Contact tips for welding with welding wire in torches

• Contact tips for welding with welding wire in torches