Workshop Tools

• Power Probe OBD II Breakout Testing Box
• Tests DLC (OBD port) for any abnormalities, such as shorting or reverse polarity at the pins before connecting other diagnostic equipment.
• quickly accss all 16 pins connections during repair and diagnosois of the vehicle

• Voltage Monitoring Range: 7.0V to 30.0V DC input
• Maximum Load: Up to 3.0A output
• Overload Protection: PTC self-healing fuse
• LED Displays: 3-digit resolution of 0.1V
• Banana Sockets: 16 outputs with 1.0mm diameter and LED indicators
• Protocols Detected: PWM (J1850)
• VPW (J1850)
• ISO 9141-2
• DIS/ISO 14230-4
• CAN bus (J-2284)
• Temperature Range: Suitable for automotive environments
• Humidity Tolerance: Less than 70%
• Cable Length: 30 inches (0.8 meters)
• Polarity Protection: Detects reverse polarity with red LED for pins 4 and 5
• Voltage Alerts: Slow beeps for low voltage (<11.8V for 12V systems)
• fast beeps for high voltage (>15.5V for 12V systems)
• Diagnostic Features: Monitors individual pins for voltage presence
• detects communication protocol signals
• DLC Connector Flashlight: Built-in light for easier connection
• Battery Type for Flashlight: CR1220 coin battery.

• Signal Locking will show the correct direction to a short to ground
• Signal distance bar indicates distance height from short to ground or open circuits
• LED light on receiver illuminates the work space area
• Longer 10-minute Auto shut off time

• Operating Voltage (Transmitter): 6V-48V DC
• Current Consumption (Transmitter): <200mA
• Operating Voltage (Receiver): 2 AAA batteries
• Signal Frequency: 4kHz polarized signal
• Circuit Testing Modes: Open circuit tracking
• short circuit tracking
• ground circuit tracking
• Operating Temperature: Up to 50°C
• Storage Temperature: Up to 70°C
• Maximum Humidity: 80% non-condensing
• Altitude Limit: <2000m
• Signal Detection: Indicates short and open circuits using visual and audio cues
• Sensitivity Adjustment: Adjustable for varying signal strengths
• Auto Shutoff: Receiver turns off after 10 minutes of inactivity
• Accessories Compatibility: Standard 4mm banana jack connectors for custom adapters
• Cable Length: 6m transmitter power cable for extended reach.

• ADJUSTABLE DUTY CYCLE from 5% to 100% with side buttons
• COMPATABLE WITH all Power Probe models with a 4mm banana jack in/out
• EASY INSTALL by removing power probe tip and inserting adapter into banana jack
• GREAT FOR diagnosing circuit fan issues

• Voltage Range: Operates between 9V and 24V DC
• Current Capacity: Maximum 40A output
• Frequency Range: Adjustable pulse width modulation (PWM) frequency from 10Hz to 200Hz
• Duty Cycle Range: Adjustable from 0% to 100%
• Input Protection: Overvoltage and reverse polarity protection
• Output Control: Variable output power via rotary dial
• Dimensions: Compact enclosure design for portability
• Connection Interface: Equipped with standard terminals for easy wiring
• Operating Temperature: -20°C to 60°C
• Housing: Durable and lightweight for automotive or workshop use
• Indicators: LED indicators for power status and output activity.

• Reduces the Power Probe tip battery voltage to 5V and limits the current output works with PP3EZREDAS
• Simple add-on accessory that works with all Power Probes with 4mm banana tip
• Safely simulate sensor reference voltages and outputs without damaging components

• Voltage Output: 5V regulated output
• Connector Type: Standard 4mm banana connector
• Compatibility: Works with Power Probe Circuit Testers (PPBasic, PP3 Series, PP4 Series, Pro Series)
• Adapter Requirement for Older Models: Requires banana jack conversion kit (#PNLS020A) for PP1 and PP2 models
• LED Indicator: Red LED illuminates to show active 5V output
• Ground Connection: Includes auxiliary ground lead clip for secure grounding
• Durability: Built with rugged materials for long-term use
• Use Case: Supplies a stable 5V to test circuits and components in vehicles
• Dimensions and Weight: Compact and lightweight for easy portability.

• Service Your Vehicles Safely: Electric and hybrid vehicles feature battery systems that need to be disconnected to prevent error or shock prior to service; Use the Power Probe VT750 LCD Car Voltage Meter Tester to ensure your battery voltage reads zero be
• Reliable Detection for Optimal Safety: Auto electric tester tool has a voltage rating from 12 to 750 volts and overvoltage protection up to 1000 volts AC/DC
• Compact Two-Prong Design: 9.4-inch (23.9cm) fixed probe housing and secondary electrical tester pole work together to prevent false readings and measure accurate, exact voltage (AC/DC) current
• Quality You Can Trust: Thick material ensures durability for the volt meter, while the retracting insulators help prevent any accidental shorts between the probes or surrounding objects
• Easy To Use: 10 minutes after disconnecting the 12-volt and high-volt batteries, complete a Live-Dead-Live test; Check 12v battery for a baseline, check high-volt battery for a dead or zero reading, then re-verify the electrical meter is still functioning

• Voltage Testing Range: 12V to 750V AC/DC
• Continuity Testing: Audible beep for continuity detection
• Display: LCD with clear digital readings
• Voltage Indication: Provides AC and DC voltage differentiation
• Polarity Detection: Identifies positive and negative poles
• Safety Compliance: CAT III 750V certification
• Response Time: Quick response for voltage and continuity checks
• Overvoltage Protection: Protects the device during high voltage surges
• Power Source: No batteries required, powered by the voltage under test
• Operating Environment: Designed for 0°C to 40°C, with 80% relative humidity tolerance
• Build Quality: Durable, ergonomic design with protective housing
• Probes: Integrated test probes with secure connectors.

Safety information

Safety First Read the operating and safety instruction. Follow them carefully. Maximum safe operating pressure 9 bar (125 psi). Air lines are dangerous - use them correctly Putting into service Before use check cap-retaining screws are secure.If the Air tool is dropped check for cracked components. Check air line pressure before connecting the Air tool.The Air tool should be used only by people trained in the use of pneumatically operated tools. Use Keep hands away from moving parts. Never operate the Air tool near the face or body. Only use Air tool to fit CV boots. If air line pressure exceeds 9 bar fit a regulator. Disconnect the Air tool from the air supply after use.

Installation Information

Operation: 1. Slide boot onto arms, large end first. The arms should just protrude from the small end of the boot. To fit a boot to an inner joint, turn the boot inside out before sliding i onto the Airtools´s arm. 2. Press " + " button until arms open enough to pass over the joint. Keep hands clear of moving parts. The air line can now be disconnected. The arms will remain open until the " - " button is pressed. 3. Place Airtool over CV joint and press release button (" -"). Keep hands away from moving parts. 4. Withdraw the Airtool, leaving the boot in position. Complete the installation in the normal way.

• Compact tyre inflator
• Inflates a 13” tyre in 4.5 minutes
• Analogue display
• 3m power cable
• Easy to use
• Complete with three-piece adaptor kit

• Rubber tread plate and feet
• 600mm flexible air hose and tyre valve thumb lock
• Large digital display to see in any light
• Analogue gauge showing PSI, BAR
• Adaptors for using with bicycle tyres, sports balls

• Complete with 2 piece adaptor kit for bikes; air beds and other inflatables
• Easy to read digital display
• Compact for easy storage and transportation
• Built in white LED light
• Rechargeable with power bank function
• 4 programmable pressure settings with digital autostop for ease of use
• Inflates bicycle tyre in <2 minutes
• Versatile - Ideal for cars; motorbikes and bicycles

• EU Conforms: Electromagnetic Compatibility - Directive 2014/30/EU Restriction of Hazardous Substances (RoHS) - Directive 2015/863/EU Regulation (EC) No1907/2006 - REACH Machinery Directive 2006/42/EC UK Comforms: Electromagnetic Compatibility Regulations 2016 Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment Regulations 2012 Regulation (EC) No1907/2006 - REACH Supply of Machinery (Safety) Regulations 2008